Wanted Emmons Push Pull parts
Fri Nov 20, 2020 10:28 am
Hello.
Became a member in the pushpull family.
I have an Emmons Push Pull D10 from 1982. Wich is a 8 + 4.
Now im planing on upgrading it to 8 + 8.
Ill add a vertical kneelever for the E9th
For the C6th one the left knee; left right and vertical levers.
Heres what im looking for:
Kneelevers left and right. (one attatched on crosshaft other with baseplate)
Vertical kneelevers 2x
4 crosshafts.
8 collars for crosshafts.
8 - 10 bellcranks with swivels.
3 1/2 bellcrank.
extra swivels if possible.
adjustable swivels (two if possible)
rod collars (20 - 30?)
4 adjustable kneelever stops
Email me at [email protected]
Became a member in the pushpull family.
I have an Emmons Push Pull D10 from 1982. Wich is a 8 + 4.
Now im planing on upgrading it to 8 + 8.
Ill add a vertical kneelever for the E9th
For the C6th one the left knee; left right and vertical levers.
Heres what im looking for:
Kneelevers left and right. (one attatched on crosshaft other with baseplate)
Vertical kneelevers 2x
4 crosshafts.
8 collars for crosshafts.
8 - 10 bellcranks with swivels.
3 1/2 bellcrank.
extra swivels if possible.
adjustable swivels (two if possible)
rod collars (20 - 30?)
4 adjustable kneelever stops
Email me at [email protected]
Re: Wanted Emmons Push Pull parts
Fri Nov 20, 2020 6:32 pm
Hi Jani
I get all of my Emmons p/p parts from Michael Yahl, Billy Knowles and Clem Schmitz - all from the USA. Michael and Clem both make their own parts, and Clem in particular designs some very nifty parts, like clip on bell cranks which can overcome having to remove cross shafts. I bought a vertical lever kit from Billy Knowles and it was very easy to fit.
I think I'm right in saying that Scotland's Bob Adams also has some parts for the push pull guitar. Bob is very helpful and knows the push pull very well. His web site on www.http://www.pedalsteel.co.uk/ is very comprehensive and gives his contact details too.
Hope you're keeping well. Ken.
I get all of my Emmons p/p parts from Michael Yahl, Billy Knowles and Clem Schmitz - all from the USA. Michael and Clem both make their own parts, and Clem in particular designs some very nifty parts, like clip on bell cranks which can overcome having to remove cross shafts. I bought a vertical lever kit from Billy Knowles and it was very easy to fit.
I think I'm right in saying that Scotland's Bob Adams also has some parts for the push pull guitar. Bob is very helpful and knows the push pull very well. His web site on www.http://www.pedalsteel.co.uk/ is very comprehensive and gives his contact details too.
Hope you're keeping well. Ken.
Re: Wanted Emmons Push Pull parts
Fri Nov 20, 2020 11:26 pm
Hi Jani, hoortivoorti von skoordy chicken in de basket.
I can concur with Ken, Bob Adams makes some tasty parts for Emmons guitars, he has just manufactured 2 new lever kits and fitted them to my old P/P and he also changed my copedent to the match my Mullen. He is also an absolute Gentleman to deal with.
Hope this is helpful to you.and I trust you are well my friend
Asleep at the steel
I can concur with Ken, Bob Adams makes some tasty parts for Emmons guitars, he has just manufactured 2 new lever kits and fitted them to my old P/P and he also changed my copedent to the match my Mullen. He is also an absolute Gentleman to deal with.
Hope this is helpful to you.and I trust you are well my friend
Asleep at the steel
Re: Wanted Emmons Push Pull parts
Sat Nov 21, 2020 10:24 am
Hi Jani, if Bob cannot fix you up I may be able to spare a few bits, is this Sami's old Emmons? I wondered where it went.
Re: Wanted Emmons Push Pull parts
Sat Nov 21, 2020 12:09 pm
JohnDavisStringsHere wrote:Hi Jani, if Bob cannot fix you up I may be able to spare a few bits, is this Sami's old Emmons? I wondered where it went.
Hi John!
yes thats exacly Samis guitar i bought. Just let me know what you have in store. or email me [email protected]
Re: Wanted Emmons Push Pull parts
Fri Dec 04, 2020 6:18 pm
Not sure where you're at with this but this is what I can do if required.
The cross shafts (to hand) are 150mm approx (a couple slightly over and a couple slightly under) these however can be made to a specific size if required.
I've put in the D10 pedal cross shaft in case you fancy going to nine!! I know what you're like!!!
Bob
ps: Looking back up your requirements here your email differs to your initial post however stops etc., not an issue.
A little personal note for the wider community from one who is and should be officially retired! I do all things pedal steel as a labour of love for the continuity of our steel community. Many of our instruments are long since out of production and parts are scarce to find so making them can sometimes be the only option.
Any parts I provide are on a no profit making basis, some items I have purchased with appropriate cost and some items I make (likewise) with appropriate cost. For the 'foreseeable future' I will always endeavour to provide what I can at the best possible price and without the ridiculous charges applied when we have to import!
The cross shafts (to hand) are 150mm approx (a couple slightly over and a couple slightly under) these however can be made to a specific size if required.
I've put in the D10 pedal cross shaft in case you fancy going to nine!! I know what you're like!!!
Bobps: Looking back up your requirements here your email differs to your initial post however stops etc., not an issue.
A little personal note for the wider community from one who is and should be officially retired! I do all things pedal steel as a labour of love for the continuity of our steel community. Many of our instruments are long since out of production and parts are scarce to find so making them can sometimes be the only option.
Any parts I provide are on a no profit making basis, some items I have purchased with appropriate cost and some items I make (likewise) with appropriate cost. For the 'foreseeable future' I will always endeavour to provide what I can at the best possible price and without the ridiculous charges applied when we have to import!
- Attachments
-
Re: Wanted Emmons Push Pull parts
Sat Dec 05, 2020 12:22 am
Nice one Bob
Re: Wanted Emmons Push Pull parts
Sat Dec 05, 2020 5:03 pm
bob adams wrote:Not sure where you're at with this but this is what I can do if required.
The cross shafts (to hand) are 150mm approx (a couple slightly over and a couple slightly under) these however can be made to a specific size if required.
I've put in the D10 pedal cross shaft in case you fancy going to nine!! I know what you're like!!!
ps: Looking back up your requirements here your email differs to your initial post however stops etc., not an issue.
A little personal note for the wider community from one who is and should be officially retired! I do all things pedal steel as a labour of love for the continuity of our steel community. Many of our instruments are long since out of production and parts are scarce to find so making them can sometimes be the only option.
Any parts I provide are on a no profit making basis, some items I have purchased with appropriate cost and some items I make (likewise) with appropriate cost. For the 'foreseeable future' I will always endeavour to provide what I can at the best possible price and without the ridiculous charges applied when we have to import!
Bob i sent you a pm
Re: Wanted Emmons Push Pull parts
Sat Dec 05, 2020 9:27 pm
Got it and returned! Regards, Bob
Re: Wanted Emmons Push Pull parts
Sun Dec 06, 2020 11:04 am
Cor Blimey Bob, those parts of yours look great, and I'm well chuffed that one of our own is making new parts for our old pride and joys. I will be in touch after Christmas for a couple of polished long handle p/p lever kits (LKL & LKR) for my C6 neck. One area that you might want to consider that would be popular are clip-on lever flags. I fitted a couple that I made onto my RKR and LKR on my p/p, and they made a huge difference. Keep up the good work buddy, and early Christmas wishes to you and Olly.
