Page 1 of 1
I am not saying it will work but, here tis
Posted:
Fri Jul 05, 2019 7:55 amby JohnDavisStringsHere
This is on my worktop now it is my version of a pull release, I figure if you work out the double raise and the lower on the 4th string .....the rest should fall into line and be easy right ??? probably get a deafening silence on this one but ,opinions helpful comments all welcome here but this "Guitar" was a blank canvas to me so just having fun with it.
Re: I am not saying it will work but, here tis
Posted:
Fri Jul 05, 2019 4:22 pmby bob adams
Hi John, I worked on a single finger Maverick recently. One finger meant for all raise or all lower not both.
It is difficult to get an accurate raise and lower even with defined balancing springs.
My compromise was a half raise lever on the fourth and a lower on the eighth.
For the top chord he could get the Eb on the open 2nd string instead of the 4th lower anyway so could achieve it all, just a different grip.
A thought perhaps?
Re: I am not saying it will work but, here tis
Posted:
Sat Jul 06, 2019 8:59 amby Zebedee
Take a look at the diagrams on this site to see how the spring-loaded lowering rod works
http://steelguitarbuilder.com/forum/vie ... ?f=4&t=508As for the double raise, it's always helpful to have fine-tuners on the bellcranks, it makes initial setup a doddle
Re: I am not saying it will work but, here tis
Posted:
Sat Jul 06, 2019 7:17 pmby JohnDavisStringsHere
Thanks for the input guys and for the diagram Richard I should have looked for that before I started !! anyway , I just made it up as I went along with the material i had to hand if you dissect it I reckon the idea is pretty much the same but maybe it would work better with the spring at the end I dont know.
Where I am at now I have raise and lower on both E's and I am getting ready to install the rest of the rods..... will keep you posted 
Re: I am not saying it will work but, here tis
Posted:
Sun Jul 07, 2019 8:51 amby JohnDavisStringsHere
OK here is the latest all rodded up and ready to go But! I cannot try it yet until I build a pedal board for it and the ally should be here tomoz
Re: I am not saying it will work but, here tis
Posted:
Sun Jul 07, 2019 9:29 amby Uncle Roy
Now looking good JD.
Re: I am not saying it will work but, here tis
Posted:
Sat Jul 13, 2019 3:11 pmby JohnDavisStringsHere
Well!! looks ain't everything Uncle Roy I am not att all happy with it, by this time I reckon I am 550 into it and looking to get my money back if I can 
It needs to go to someone who does not mind getting to grips with the pull release system and making it work properly..... I reckon it is beyond me 
This is as good as it gets............
Re: I am not saying it will work but, here tis
Posted:
Sun Jul 14, 2019 1:29 pmby slimbo
Hi John, this steel with a couple of pedals fitted would make an excellent C6 ten, only saying this because my interest in the standard country or today's country has faded, but my interest in Western Swing has evolved and become quite exciting, well, at home anyway, and not too many C6 10 strings around now unless your dragging one around on the back of an E9.
Go on, string it up to C6 with two or three pedal's, bet it will go.
Re: I am not saying it will work but, here tis
Posted:
Sun Jul 14, 2019 6:32 pmby JohnDavisStringsHere
thank you Slim but it's gone already.......on it's way to Cornwall......